EnergyFit Visalia Insulation Solutions insulates attics, walls and crawl spaces in Dinuba, CA. We seal the gaps first and insulate second, so the drafty bedroom and the room over the garage stop fighting the rest of the house.
Dinuba is a compact city. A short drive takes you from older single-story houses near downtown to newer subdivisions on the edges, with shops and small commercial buildings in between. We come up from Visalia for these jobs, the same way we cover Kingsburg and Woodlake, so the calls here sound familiar: a hot upstairs, cold floors, a power bill that keeps climbing.
The older houses usually have a tight attic and a crawl space, with insulation that's packed down over the years and gaps around wiring nobody sealed. The newer ones are easier to get into, but the coverage often runs thin at the edges. What's up there now decides whether we start by removing, sealing or just adding.
When ducts run through the attic or a room sits over the garage, foam seals and insulates in one pass. I'll tell you plainly whether it's worth the higher cost for your house.
Explore serviceWe measure how many inches are already up there, seal the gaps, then bring the whole attic up evenly, out to the eaves.
Explore serviceBlown-in insulation is loose fill blown through a hose, and it suits the shallow attics in older Dinuba houses because it reaches corners nobody can crawl into.
Explore serviceWe look at the attic, walls and crawl space together, so we fix the part that's actually making the house uncomfortable first.
Explore serviceInsulation that's been soaked, flattened or filled with droppings comes out before anything new goes in, because covering it keeps the problem.
Explore serviceFor cold floors in raised older houses, we insulate under the floor once we know the crawl space below it is dry.
Explore serviceOlder walls that were never filled can usually be insulated from the outside or inside without opening the whole wall.
Explore serviceAir sealing means closing the gaps around pipes, wires, can lights and the hatch, so the air you pay to heat and cool stays in the rooms.
Explore serviceBasements are uncommon here, but where a house or building has one, we insulate the walls with moisture in mind from the start.
Explore serviceClosed-cell foam is a dense foam that blocks moisture, so we use it on crawl space walls and other spots where damp is the worry.
Explore serviceOpen-cell foam is softer and lighter, a good fit for rooflines and interior walls when you want air sealing without the cost of closed-cell.
Explore serviceFor shops and offices around Dinuba, we plan the insulation around tenants and the other trades, so each step happens in the right order.
Explore serviceA ground cover across the crawl space dirt keeps moisture from rising into the floor framing and the insulation above it.
Explore serviceWhere a wall, ceiling or crawl space needs a moisture layer, we put it on the side the materials and the job call for.
Explore serviceBefore any insulation goes up, we seal the hatch and every hole cut for wiring, pipes and lights, so the new layer isn't fighting a draft.
Explore serviceAdding insulation to a lived-in house means working around wiring, ducts and stored boxes, and that careful work is what we started this business to do.
Explore serviceBuilding permits here come from the City of Dinuba, through its Development Services Department, and you'll find the application on the city's permits page. Before we start, we check with the city whether your job needs one. When it does, I apply as your licensed contractor and meet the inspector on site, and the work waits on that permit, so it's the part of the schedule nobody controls. Two things you can check on any contractor working here are a current state contractor license and a City of Dinuba business license, which the city has contractors apply for. We're licensed and insured.
We're an insulation contractor based in Visalia, CA, and we work Dinuba the same way we work Selma. I come out myself, look before I price anything, and the price follows what I find: how many inches are already down, whether old material has to come out first, how many gaps need sealing, and how hard the attic or crawl space is to get into. The schedule turns on those same things plus any permit, and the written estimate, with photos of what I found, gives you the figure for your own house.
Send the form or call (559) 409-1169, and we'll reply within one business day. I come out myself to look at the attic, walls or crawl space, and the estimate is free, in writing, with photos of what I found. There's no obligation, and if part of the job should wait or belongs to another trade, the estimate says so.
(559) 409-1169A contractor needs a current license from the Contractors State License Board when the job requires a building permit, when they use employees, or when labor and materials together come to $1,000 or more. Most attic and crawl space jobs land in at least one of those. Ask for the license before anyone starts work.
The state board's rule is no more than $1,000 or 10 percent of the total contract price, whichever is less, on any home improvement job. Every payment after that has to be listed in the contract and tied to work done or materials delivered. Check the payment lines in any contract against that before you sign.
For blown-in insulation and air sealing, you can usually stay home while we work. Spray foam is different, because everyone, kids and pets included, stays out until the re-entry time passes, which is the wait the foam maker sets before you can come back inside. I'll tell you that time at the estimate, so you can plan around it.
We're based in Visalia and work across the cities around it, from Kingsburg and Selma to Hanford, Lemoore and Woodlake. The cities with their own page are listed here. If yours isn't named, call and ask.
Call (559) 409-1169 or send the form, and if your job should wait, or part of it belongs to another trade, I'll tell you before anyone carries material up the ladder.
If something in your attic or crawl space has you wondering, send us a note and we'll talk it through.
Tell us about your project
